Parts & repair
Where do I find parts for my Ampeg…?
So you have a B-15N Portaflex and you are looking for new clasps to hold the top down. Or you have an old Jet and need 7591A power tubes. Or you need a transformer rewound. Start here.
Ampeg had a great talent not only for designing amplifiers but also for using parts that were destined to become scarce. This part of the archive is dedicated to helping you find the pieces you need to keep your amplifier or instrument healthy and working. If you are looking for something specific, ask; if you know of a source that everyone should know about, say so.
Caveat emptor
Although we have done business with a few of the sources mentioned here, we cannot vouch for all of them, and suppliers change hands, change policies and change attitudes. Nothing here is an endorsement, and none of these listings are paid for. Take the normal precautions you would take with any supplier you have not used before.
A note on this page
The suppliers below were compiled between 1995 and 1997, when this page was last revised, and the list is preserved because much of it is still the best information available for parts that nobody else stocks. Companies marked offline have closed or dropped off the internet since then; the addresses are left in place because the part numbers and the history are still useful.
On this page
General parts and repair
Looking for someone to fix your amplifier? Someone who just might be able to supply the missing logo or piece of blue-checked Tolex? Try contacting Gregg Hopkins at Vintage Amp Restoration, who loves Ampegs as much as you do. Besides cosmetic and electronic repairs and restoration of Ampegs and other brands, Vintage Amp manufactures covers, and Gregg is good to deal with. Gregg also gets rave reviews for his speaker recone jobs.
Also available from Vintage Amp Restoration: replacement tremolo modules (see below), late-1960s and 1970s blue and silver grille cloth made by the original manufacturer, metal foot cups that go on top of some cabinets and on the bottom of cabinets with dollys, reproduction script logoplates, blue leather amplifier handles and the rubber shock mounts that attach and isolate a Portaflex chassis from the flip-over top board. These parts are made by the original manufacturer. Contact Gregg for more information.
Another source of Ampeg repairs, originally focusing on Portaflexes but now branching out to provide parts for other Ampeg models, is Fliptops. The range of available parts, both NOS and reproduction, has grown steadily over the years. They even carry reproduction tube cages and a selection of NOS transformers.
In the United Kingdom, try NSSC — The Northern Synthesizer Service Centre, 153 Sunbridge Road, Bradford, BD1 2NU, England; telephone and fax +44 (0) 1274 777 300. Trevor reports that they have been servicing Ampeg for many years.
If you have an old Ampeg horizontal bass and need a part reproduced, or you would like an instrument built from scratch, contact Bruce Johnson at Johnson's Extremely Strange Musical Instrument Co., 119 W. Linden Ave, Burbank, CA 91502. There is more about Bruce and these instruments on the horizontal basses page.
Trying to find those extra-extra-long scale strings to fit Ampeg AEB-1, AUB-1 and ASB-1 basses? Bruce Johnson has them, in both flatwound and roundwound sets by D'Addario, and has carried other brands from time to time. Contact him to find out what is currently available.
The Bass Centre, which used to stock Ampeg-length strings, has closed its doors. offline
Tubes
Tubes are probably the single most sought-after part for old Ampeg amplifiers. Some of the types used have since become rare and expensive. Ampegs have used the 7027A, 12DW7, 7199, 7591 and 6BK11, to name a few, and all of them command premium prices. They are still available if you look hard enough, but do not expect to walk into a local guitar shop and find them.
Fortunately, interest in tube circuitry is on the rise, and factories outside the United States have added some of these types back to their production lines. The 7199, for instance, has been manufactured in Russia and marketed by Sovtek, although it has been reported that the Sovtek 7199 is not a true 7199 but merely pin-compatible. The same has been said of their 5Y3 and their 5881: many former Soviet types are similar to the desired valve without being quite the same, and are numbered as though they were. The 6BK11 has also appeared in Sovtek advertising, and Sovtek has taken requests for a run of 7591s. Svetlana has produced a 7591A at its St. Petersburg plant. Be patient, and do not damage your amplifier with a valve that is not right for it.
On tube quality generally: valves from every manufacturing country have varied enormously over the decades, and the sound and reliability of any given valve depend far more on the individual factory, the era of production and how the valve has been stored and used than on its country of origin. Modern production from Russia, Slovakia, China and elsewhere has improved considerably, and the practical approach is to buy from a supplier who tests and grades what they sell, and who will stand behind it. Whatever you choose, have the amplifier biased correctly for the valves you fit, and buy matched output sets.
One place to try for tubes is Angela Instruments. They are not the cheapest for everything, though their tubes are competitively priced, and they have carried a good stock of NOS 7027A power tubes. Angela also carries capacitors and other electronic parts that may have failed in your amplifier. They do not have a lot of Ampeg-specific stock, although you might be lucky and find a transformer.
Another place to try is Antique Electronic Supply, 6221 S. Maple Avenue, Tempe, AZ 85283. They have a long-standing reputation for helpfulness.
A good list of tube suppliers and other parts sources can be found at AMPAGE, a very well put together site catering to enthusiasts of all brands of amplifier.
Regarding 7027A tubes: you can stop worrying about whether to convert your V-4, B-25B and similar amplifiers to a different type. Ned Carlson's 7027A FAQ explains that a 6L6GC can be used as a direct plug-in replacement for a 7027A, at least in Ampegs — read the page before you do it. Note that the text is Ned's, and that some people disagree with him, but Ned is a regular and respected contributor to the guitar amplifier community. Ned and his partner run Triode Electronics, another source for tubes and related parts.
Other electronics
Many electronic parts such as capacitors and transformers can be found at Angela Instruments and Antique Electronic Supply, both listed above.
Transformers, replacement and rewinding
People often ask about replacing or rewinding a dead transformer. There is no single place where you can reliably find a range of NOS or reissue Ampeg transformers for every model. Mojo carries Portaflex transformers, at a cost of roughly $200 — for that money it is worth considering a trashed amplifier with good transformers, which leaves you with a great many other spare parts as well.
One option when a transformer fails, especially if originality matters, is to have it rewound. Aspen Pittman of Groove Tubes recommended calling Craig Swancy at Craig's Music in Weatherford, Texas; (817) 599-8021. Craig has a technician who custom-winds almost anything you want, and knows enough to re-engineer a transformer from your old one using the same core. For transformer rewinding, Dixie Sound Works, 372A Gunter Avenue, Guntersville, AL 35976; (205) 582-2425, fax (205) 582-6681, comes recommended: the first time they encounter a particular transformer they make careful notes on the specifications as they unwind it and reverse-engineer it, so the next time that type is needed they already have the specifications.
Insist on interleaved windings
If you have an output transformer rewound, ask specifically for interleaved windings. This means a layer of primary winding is followed by a layer of secondary, then primary again, and so on until the windings are finished. That is how output transformers were wound when your amplifier was new, but it is faster and cheaper to wind all of the primary and then all of the secondary, so many modern transformers are wound that inferior way. It makes an audible difference to the tone of the amplifier. Note that this applies to output transformers, not to mains transformers.
Tremolo modules
The tremolo module used in some Geminis, Reverberockets and other models — an optoisolator arrangement with a lamp and a photoresistor in one package — was formerly unavailable, but is now replaceable. A direct drop-in replacement has been produced, and according to an official source it preserves the afterbeat that other replacement attempts could not retain. If your tremolo is dead and you would like to get your amplifier shaking again, the part is available from Vintage Amp Restoration. See above.
If you must have the original part, Antique Electronic Supply has carried the elusive tremolo module, at a price reported to be as high as $130, although this has not been confirmed.
Electronic service
Central Jersey Music Services, (908) 572-1911, is worth singling out because it is the shop where Dennis Kager does the repairs. Dennis worked in the Ampeg factory in Linden, New Jersey, and may well have had his hands on your amplifier once before. Dennis asks that you not call him about parts — he does not have tremolo modules, grille cloth or logoplates. As he put it, “these parts were tough to get before these amps became antiquity”. So do not call him for parts, but if you can get your amplifier to him, you will not find better service.
Hardware
Ampeg bought much of its hardware, such as clasps and corners, from Excelsior Hardware in Stamford, Connecticut. Excelsior went out of business in 1995, but much of their stock went to Luggage and Handbag Supply, 284 East Arrow Highway, San Dimas, California 91773; (909) 394-1213. Part numbers worth knowing:
- 2801 Corners — the “three-finger” corner found on the old Jet and other blue-check beauties
- 2403-X Clawbolt Catches — the clasps holding down the top of a Portaflex
- 195 Bell Studs, 8/16" — the nickel hemispherical feet on the bottom
They do not have the two-leg wrap-around lipped corner in the correct size. If you are less particular, Peavey wrap-around corners are close to the original.
It has been reported that Luggage and Handbag Supply can be difficult to deal with and now has a $50 minimum order. Ordering your parts from Vintage Amp Restoration instead is often easier. See above. status uncertain
Metal foot cups, found on the top of some cabinets and on the bottom of cabinets with dollys, are also available, along with much of the hardware mentioned above, reproduction script logos, Portaflex chassis shock mounts and blue leather handles with their mounts, from Vintage Amp Restoration.
The large chrome-plated handles fitted to the larger Portaflexes were manufactured by Kason Industries Inc., 150-32A 12th Road, Whitestone, NY 11357-1810; phone (718) 767-3737, fax (718) 767-3972. Kason is still in business. The part number has changed from #577 to #573.
The rubber shock feet on the Portaflex dolly are nothing more than number 4 single-hole black rubber laboratory stoppers.
The clutch screws that Ampeg used are common in mobile homes and recreational vehicles, and are likely to be found at a mobile home or RV repair facility.
Baby Bass parts
Many parts are available for the Ampeg Baby Bass, either NOS or as new parts that do the job better than the originals. Start with the Baby Bass page for background on the instrument itself.
Subway Guitars, 1800 Cedar Street, Berkeley, California; (510) 841-4105, has had the original jig for cutting necks, as well as a stock of tailpieces and other parts. Whether they will sell you one is up to them. offline
Someone who manufactures replacement necks is Ray Ramirez, 20 Esmeralda Street, Humacao, Puerto Rico 00791; (809) 852-6678. He also manufactures other components and makes his own Caribbean Baby Bass entirely from wood. Parts Mr. Ramirez can supply include tuning machines in chrome, black or gold; Thomastik Spirocore or Super Flexible string sets; gig bags; wooden bridges; and tailpieces in maga or ebony. Services include pickup bobbin rewinding, pickup maintenance and pot cleaning, potentiometer replacement, fingerboard levelling and neck replacement. website offline
Someone in New Jersey rebuilds pickup bobbins for the Baby Bass pickup assembly: Lue Rosa, (908) 985-3333.
If you are dissatisfied with the stock pickup and want a better sound out of your Baby Bass, and you do not want to try making your own pickup, call Steve Azola at Azola Instruments, 382 Enterprise Street, #108, San Marcos, California 92069; (619) 591-9162. Besides manufacturing his own updated Baby Bass, Steve produces retrofit pickups for Ampeg Baby Basses that bring the instrument into the present. He offers several configurations.
Parts wanted
Slowly, sources are being found for many formerly unattainable parts. Some parts are still wanted and unavailable:
- Late-1960s and 1970s “block” logoplates, although Ampeg offers a similar logo
- Portaflex tube cage thumbscrews
- A reliable source of transformers
- The correct two-leg wrap-around lipped cabinet corner
If you have any of these, or you know where to find them, please get in touch.
Related pages
Relevant links
The checked link list: suppliers, archives and builders, marked with whether they are still online.
See the links →
Schematics
Nearly fifty free diagrams, so you know what part you are actually looking for.
Browse schematics →
Tube amp safety
Before you fit any of these parts yourself, read this.
Safety guide →
Page created 2 October 1995; last modified 20 November 1997. External links re-checked and marked; supplier details preserved as published.