Instruments · Project

Making a new pickup for the Ampeg Baby Bass

Want a better sound out of your Baby Bass without making irreversible modifications? Either order a replacement pickup from a specialist, or try your hand at making your own. Here is how it was done.

This page was missing for years

The Baby Bass pickup project was one of the most useful pages on the original site, and the link to it was broken for a long time. The text has been recovered from an archived copy and restored to the same URL, with the images and advertising code of the time removed.

Warning

This is a description of what one person did, not a set of instructions with any guarantee attached. Nobody is responsible if you damage your bass, and a drill press or a razor used carelessly will injure you. If you do not know what you are doing, and how to do it safely, do not do it. If you are not comfortable with woodwork or soldering, a specialist can supply a retrofit pickup that requires no modification at all — see the Baby Bass parts section of the parts page.

What you need

Materials

  • A miniature piezo buzzer element — the original used a RadioShack part, number 273-064, which cost about $1.79
  • Quarter-sawn rock maple for a new bridge
  • A mono output jack
  • Shielded cable
  • Cork, thin slices of it

Tools

  • A soldering iron
  • A razor or a very sharp knife
  • A saw and files for shaping the bridge blank
  • Sandpaper

Step 1: make a maple bridge

The first thing done was to replace the aluminium bridge with a maple one. A quarter-size double bass bridge will reportedly fit, but the original was cut from rock maple. If you cannot find a piece of quarter-sawn maple, at least make sure the grain runs across the width of the bridge and not top to bottom.

Trace the outline of the aluminium bridge onto the maple, cut it out, and form the blank into a wedge. Cut the scrollwork into the bridge as well, so that you have the two slots on the side that are common to violin-family bridges. Bridgemaking is a craft in its own right; if you do not know anything about woodworking, find somebody who does.

Step 2: prepare the piezo element

Buy a miniature piezo buzzer element. Carefully pry open the plastic casing. Inside you will see a brass disk with the piezo crystal on it and three wires coming from it. Remove the feedback wire, which is blue. Then carefully scrape off the white ring of silicone that glued the element into the casing.

Step 3: wire the element to a jack

Solder the red wire to the centre conductor at one end of a short length of shielded cable. Solder the black wire to the shield of the same cable. At the other end, solder the centre conductor to the tip connection of the mono jack and the shield to the sleeve.

Why shielded cable matters

A piezo element produces a high-impedance, low-level signal and picks up hum very easily. The shield is not optional — it is the difference between a usable pickup and a noise generator.

Step 4: sandwich the element in cork

Make a piezo sandwich by putting the element between two thin slices of cork. Carefully slicing sections from a wine bottle cork with a razor gives round sections of about the right size; sand them smooth and to the right thickness, which is determined by trial and error. Take the element, sandwiched between the two slices of cork, and push it into the slot on one side of the maple bridge. The fit should be rather tight.

Step 5: secure the output jack

Fashion some way to secure the output jack to the strings below the tailpiece, in the manner of a Fishman pickup. The temporary arrangement used at the time was a large paper clip in front of the strings and another behind them, pushing the jack through the centre and screwing the nut down in front of it. A more permanent arrangement is worth the effort.

Step 6: plug in and position the element

Now it is time to plug the bass in. Be careful: the new pickup was considerably louder than a Precision Bass, so turn the amplifier volume down before you start. You may have to reposition the element in the slot a few times to find where you get the best response. The result should be a bass sound that puts the stock pickup to shame.

Taking it further

The next step is to add a volume control and, perhaps, an active or passive tone control. If you have done this sort of work and can refine the procedure or offer other options, please get in touch.


Alternatives, if this is not for you

Buy a retrofit pickup

Specialists produce retrofit pickups for the Ampeg Baby Bass in several configurations. They fit the original instrument — no woodwork, no irreversible modification — and bring the sound up to date.

Baby Bass parts and services →

Get more from the original

Before replacing anything, try a parametric equaliser: boost the mids, sweep the frequency control until the nasal quality is at its worst, then notch that frequency out. Damping the strings between the bridge and the tailpiece helps too.

About the Baby Bass →


← Baby Bass  ·  Baby Bass parts  ·  Dan Armstrong PDF

Page created 2 October 1995. Restored from the Wayback Machine archive after the original link broke.