Reference
Glossary of Ampeg and valve amplifier terms
The vocabulary of Ampeg collecting: cabinet coverings, logoplates, circuit terms and the model-code conventions, defined so that listings can be read with suspicion.
These definitions are written for people who are new to vintage amplifiers as much as for people who already know the subject. Where a term is used loosely in the marketplace, that looseness is noted.
Coverings and cabinet terms
- Blue check
- The navy-blue vinyl with a random glitter, check or sparkle pattern used from 1962 and the single most recognisable Ampeg cosmetic. “Blue check” is the term most collectors use; some listings call it “blue random”. It defines the golden era more than any other single feature, and a 1960s Portaflex without it has usually been recovered.
- Random
- Used of covering materials with an irregularly scattered pattern, as distinct from a repeating one.
- Treebark
- A covering with a deeply textured, bark-like surface, used on early amplifiers in light tan or grey.
- Tolex
- Strictly a brand name for a particular vinyl, but used generically for cabinet covering. Most of what Ampeg used was not Tolex brand, so “Tolex” in a listing tells you nothing about originality.
- Flocked grille
- A grille cloth with a velvety, raised surface, produced by dusting adhesive-coated fabric with short fibres. Used on early Ampeg amplifiers.
- Swirl
- A grille cloth pattern with a marbled or swirled finish, seen in red, black and grey versions.
- Diamond pattern
- A grille cloth with a woven diamond figure, seen on tan grilles.
- Tight blue and silver weave
- The late-1960s and 1970s grille cloth: a dense weave of blue and silver threads. Reproductions made on the original manufacturer's equipment are available.
- Burlap
- A rough, coarse weave used on some early-1980s cabinets.
- Logoplate
- The metal plate carrying the Ampeg name. Earlier plates are diecast script in nickel, chrome or copper; later ones are the square “a” badge in metal or plastic; the 1970s plates are wider “block” designs. Reproduction script plates are available, and reproduction is not the same as original.
- Tube cage
- The perforated metal cover over the valves on some Portaflexes. They are frequently missing, and the thumbscrews that retain them are almost always missing. Reproduction cages are available.
- Shock mounts
- The rubber mounts that attach and isolate a Portaflex chassis from the flip-over mounting board.
Portaflex and cabinet terms
- Portaflex
- Ampeg's flip-top amplifier family, introduced in 1960 with the B-15. The chassis is mounted in a board that hinges at the back; the amplifier is transported with the board flipped over and the valves facing into the cabinet, and flipped back for use.
- Flip-top
- The mechanism described above, designed and patented by Jess Oliver. The name describes the cabinet, not a speaker type.
- Reflex cabinet
- A cabinet with a tuned opening or port rather than a sealed or fully open back, used to extend low-frequency response. The Portaflex cabinet is a closed-back reflex design with double-baffle porting.
- Double baffle
- Two layers of baffle board, with the port formed between them.
- Dolly
- The wheeled platform that some larger cabinets, particularly the B-18, sit on.
- Foot cups
- The metal cups fitted to the tops of some cabinets and the bottoms of cabinets with dollys, so that stacked cabinets locate positively.
- Clawbolt catch
- The type of clasp used to hold the Portaflex top down. Excelsior hardware part 2403-X.
- Bell stud
- The nickel hemispherical foot on the bottom of a cabinet. Excelsior hardware part 195.
- Three-finger corner
- The cabinet corner with three legs, found on early Ampegs. Excelsior hardware part 2801.
Electrical and valve terms
- 7027A
- A power valve used in the V-4, V-4B, B-25B and many other Ampegs. It is now scarce and expensive. A 6L6GC can be used as a direct substitute in most Ampegs, but read the discussion before doing it.
- 12DW7
- A dual triode with two dissimilar halves, used in Ampeg preamps.
- 7199
- A triode-pentode used in Ampeg reverb circuits and in some other makers' amplifiers. Russian production has been marketed as a 7199, though it has been reported to be merely pin-compatible rather than equivalent.
- 7591 / 7591A
- A power valve used in the Jet, Reverberocket and other mid-1960s amplifiers. A 7591A has been produced again in Russia.
- 6BK11
- A triple triode used in some Ampeg amplifiers, including the J-12D.
- 6146B
- A transmitting valve used in the earliest SVT power amplifiers, replaced by the 6550A in later production. See both SVT schematics.
- 6550 / 6550A
- The output valve of the SVT: eight of them, for 300 watts.
- Interleaved windings
- In an output transformer, a winding pattern in which primary and secondary layers alternate. This is how transformers were made when these amplifiers were new, and it audibly affects the tone. If you have an output transformer rewound, ask for it explicitly.
- Bias
- The steady negative voltage applied to the control grid of an output valve. It must be set correctly for the valves fitted, and it must be checked whenever output valves are replaced.
- Filter capacitor
- The large capacitors that smooth the high-voltage supply. They store lethal charge after the amplifier is switched off and unplugged, and they are the most common failure in an amplifier of this age.
- Bucket brigade
- A type of analogue delay device using a chain of switched capacitors. Used in the echo circuits of the Echo Twin and in the A-series effects pedals.
- Optoisolator tremolo
- The tremolo circuit using a lamp and a photoresistor in one package, used in some Geminis, Reverberockets and other models. Replacements are available. See the parts page.
- Ultra high
- The high-frequency boost circuit found on Ampeg bass and guitar amplifiers.
Dating and collecting terms
- EIA code
- A three-digit or four-digit code identifying the component manufacturer, followed by a date code, stamped on potentiometers, transformers and speakers. It is the most reliable evidence of when an amplifier was built, and it gives the latest possible date. See the EIA code page.
- Source code
- The manufacturer identification part of an EIA code.
- NOS
- New old stock: a part that is genuinely unused and genuinely old. The term is used very loosely in the marketplace, and “NOS” in a listing should be treated as a claim to be verified rather than a fact.
- Reissue
- A new amplifier built to resemble an old one. Ampeg has issued several, most notably the B-15N reissue of 1995 and the B-15 of 1997. A reissue is not a vintage amplifier and should never be sold as one.
- Recone
- Replacing the cone, voice coil and spider of a loudspeaker while keeping the original frame. A competent recone preserves the character of an original speaker far better than replacement does.
- Orphan
- A Portaflex head without its cabinet, or a cabinet without its head. Reproduction cabinets are available for orphans.
A term we have missed?
If there is a word you have seen in an Ampeg listing that is not explained here, send it in and it will be added.